Every Watch Counts to 32 768 and Calls It a Second
Gepubliceerd op 29-10-2026 · 4 min leestijd · Dagelijkse calculators
Lena Hoffmann — Redacteur wetenschap en onderwijs bij OneKitly
Wiskunde · Natuurkunde
Getoetst aan 2 bronnen
Period is one divided by frequency, and reading that division carefully explains a good deal of ordinary machinery. A watch crystal vibrating at 32 768 Hz has a period of 30.5 microseconds; because 32 768 is two raised to the fifteenth power, a chain of fifteen flip-flops each halving the rate arrives at exactly 1 Hz, using nothing but the simplest possible digital element repeated. Mains at 50 Hz has a period of 20 ms; at 60 Hz, 16.67 ms. Concert A at 440 Hz repeats every 2.27 ms, and a microwave oven's 2.45 GHz repeats every 0.41 nanoseconds — during which light travels 12 cm, which is where the wavelength that melts your chocolate comes from.
That number is two to the fifteenth, so fifteen halvings turn the crystal's 30.5 microsecond tick into exactly one second. Nothing else about it is arbitrary either.
Why a lamp flickers at twice the mains frequency
Alternating current reverses direction twice per cycle, and a filament or an LED driver does not care which way the current is flowing — it produces light on both halves. So a 50 Hz supply gives 100 flashes a second, with a period of 10 ms rather than 20. That doubling is why cheap LED lamps can look unpleasant on camera and why the stroboscopic effect that freezes a spinning object appears at 100 Hz and its divisors. It is also the reason old film cameras were run at 24 or 25 frames per second in countries with the matching mains: a frame rate that divides evenly into the flicker keeps the banding out of the picture.
The crystal keeps better time than the mains
A cheap watch crystal drifts by around twenty parts per million, which is a minute a month — poor by laboratory standards and unremarkable in a wristwatch. Mains frequency, by contrast, is not held to any instantaneous accuracy at all; it wanders by tenths of a hertz as demand rises and falls. What operators historically corrected was the accumulated count of cycles, deliberately running fast or slow so that a clock counting cycles would show the right time by the end of the day. Several European grids stopped guaranteeing that around 2018, and mains-driven clocks in appliances have drifted noticeably since — a small piece of infrastructure whose retirement most people met as an oven that runs late.
| Source | Frequency | Period |
|---|---|---|
| Mains, Europe | 50 Hz | 20 ms |
| Mains, North America | 60 Hz | 16.67 ms |
| Concert A | 440 Hz | 2.27 ms |
| Watch crystal | 32 768 Hz | 30.5 µs |
| Microwave oven | 2.45 GHz | 0.41 ns |
Uitgewerkt met onze eigen calculator
Calculator frequentie en periode
Gegeven
- Frequentie (Hz)
- 100
Resultaat
- Periode (s)
- 0,01
- Periode (ms)
- 10
Deze cijfers komen uit de calculator hieronder, ze zijn niet met de hand ingetypt — ze worden opnieuw berekend telkens als de tool verandert.
Reken het door met je eigen cijfers →Veelgestelde vragen
- Why 32 768 and not a round number like 100 000?
- Because dividing by two is nearly free in silicon and dividing by ten is not. A flip-flop halves a frequency with a handful of transistors and no arithmetic; a divide-by-ten stage needs a counter, a comparator and a reset, which in the 1960s meant more area, more current and more to go wrong. A power of two also lands the frequency in a useful place: high enough to make a small crystal, low enough that the counting chain sips microamps, which is what lets a watch run for years on a cell the size of a lentil. Every constraint pushed toward the same answer.
- Does a longer period always mean a slower device?
- It means fewer events per second, which is not the same as less capability. A processor doing more work per clock tick can outperform a faster-clocked one, and a low-frequency radio link can carry as much as a high-frequency one if it uses the bandwidth more cleverly. Where the period does bite directly is latency: nothing that runs on a 20 ms cycle can respond to anything in less than 20 ms, however capable it is otherwise. That is why control loops for fast machinery are specified by their period rather than their throughput, and why an audio system's latency is quoted in milliseconds even though its sample rate is quoted in kilohertz.
Artikelen die je misschien interesseren
Alle gidsen →Vergelijkbare tools
Bronnen
Een fout in dit artikel gezien?