Naar de inhoud
OneKitly

How Much Roofing Material Do I Need? Area and Squares

Gepubliceerd op 9-2-2026 · 3 min leestijd · Vastgoedcalculators

Marco Bianchi

Marco Bianchi — Redacteur wonen, klussen en auto bij OneKitly

Verbouwen · Materialen

Getoetst aan 2 bronnen

Profiel bekijken →
Kort gezegd

Start with the footprint the roof covers, then multiply by a pitch factor to get the true sloped area, since a pitched roof is larger than the floor beneath it. A moderate 6:12 pitch has a factor of about 1.12. Roofing is sold in squares of 100 square feet, so a 1,500-square-foot footprint at 6:12 gives about 1,680 square feet, or roughly 17 squares before waste.

Advertentie
Tiled rooftops against a clear blue sky.
Jan van der Wolf · Pexels · Pexels

Turn your building footprint into true roof area using the roof pitch, then convert to roofing squares or square meters plus a waste allowance.

Footprint is not roof area

The floor area under a roof is smaller than the roof surface, because a slope travels farther than the flat distance it covers. To get true roof area you multiply the footprint by a pitch factor that grows with steepness — the steeper the roof, the more material a given footprint needs.

As a rough guide, a 4:12 pitch has a factor near 1.06, a 6:12 near 1.12, and a 9:12 near 1.25. Read the factor from the pitch, multiply, and you have the sloped area before any waste.

Roofing squares and coverage units

In the US, roofing is measured in squares, where one square equals 100 square feet of roof surface. Divide your true roof area by 100 to get the number of squares, which is how shingles, underlayment, and labor are usually quoted.

Whatever the unit, always convert the sloped area — not the footprint — into coverage. Ordering off the footprint under-buys every job, and the shortfall grows with the pitch of the roof.

Waste, hips, valleys, and accessories

A plain gable roof wastes little, but hips and valleys mean angled cuts and more offcuts, so allow 10% on a simple roof and up to 15% on a complex one. Add starter courses along the eaves and ridge caps along the top separately.

Don't forget the layers under the shingles: underlayment covers the same true roof area, and drip edge, flashing, and ridge vent are measured by the linear foot of eave, valley, and ridge respectively.

Uitgewerkt met onze eigen calculator

Dakshinglescalculator

Gegeven

Dakoppervlak (m²)
90
Verlies (%)
5

Resultaat

Pakken shingles
31

Deze cijfers komen uit de calculator hieronder, ze zijn niet met de hand ingetypt — ze worden opnieuw berekend telkens als de tool verandert.

Reken het door met je eigen cijfers →
Advertentie

Veelgestelde vragen

How do I convert footprint to roof area?
Multiply the footprint by a pitch factor: about 1.06 for a 4:12 pitch, 1.12 for 6:12, and 1.25 for 9:12. Steeper roofs need a larger factor.
What is a roofing square?
A roofing square equals 100 square feet of roof surface. Divide your true roof area by 100 to get squares — the unit shingles and labor are usually quoted in.
How much waste should I add for roofing?
Allow about 10% on a simple gable roof and up to 15% on a complex roof with many hips and valleys, plus starter and ridge courses separately.
Do I include the eave overhangs?
Yes. Measure the footprint out to the edge of the eave overhangs, not just the walls, since the roofing has to cover the overhang too.

Artikelen die je misschien interesseren

Alle gidsen →

Vergelijkbare tools

Bronnen

Een fout in dit artikel gezien?