A Loft Holds Exactly Half the Air of the Box Around It
Published 11/2/2026 · 3 min read · Real-estate calculators
Marco Bianchi — Home, DIY & motoring writer at OneKitly
Renovation · Materials
Checked against 2 sources
The volume of a triangular prism is the area of its triangular end times its length. A gable roof space 6 m across and 2.5 m to the ridge has an end area of 7.5 m², so over 8 m of length it encloses 60 m³. The equivalent rectangular room — same width, same length, ceiling at the ridge height throughout — would hold 120 m³. The factor of exactly two comes from the triangle being half its bounding rectangle, and it holds for any pitch: steepening the roof raises both figures together and leaves the ratio untouched.
A roof space 6 m wide, 2.5 m to the ridge and 8 m long holds 60 m³ — half the 120 m³ of a flat-ceilinged room with the same footprint and the same maximum height.
Half the air is half the heating
Per square metre of floor, the loft encloses 1.25 m³ of air against the flat-ceilinged room's 2.5 m³. Heating a volume of air to a given temperature costs in proportion to that volume, so the sloping ceiling halves that particular bill before any insulation is considered. What it does not halve is the heat loss through the roof itself, which depends on surface area rather than volume — and a pitched roof has more surface than a flat ceiling of the same footprint. The two effects pull in opposite directions, which is why the honest comparison needs both the volume from this calculator and the roof area from a separate one.
Usable space is not the same as volume
The 60 m³ includes the wedges along both eaves where the ceiling is under a metre, and nobody stands there. Building regulations in most countries count only floor area under a minimum headroom towards the habitable surface — commonly 1.8 m — so a loft with a generous volume can have a disappointing legal area. The calculator gives the physical answer and the regulation gives the saleable one, and the gap between them is where dormer windows and raised ridges earn their cost. Measure the volume to size the heating; measure the area above the headroom threshold to size the expectations.
| Ridge height | Loft volume | Flat-ceiling equivalent |
|---|---|---|
| 2.0 m | 48 m³ | 96 m³ |
| 2.5 m | 60 m³ | 120 m³ |
| 3.0 m | 72 m³ | 144 m³ |
| 4.0 m | 96 m³ | 192 m³ |
Worked with our own calculator
Triangular prism volume calculator
Given
- Triangle base
- 6
- Triangle height
- 4
- Prism length
- 10
Result
- Volume
- 120
These figures are produced by the calculator below, not typed in by hand — they are recomputed whenever the tool changes.
Run it on your own figures →Frequently asked questions
- Does the formula still work if the roof is not symmetric?
- Yes, provided the ridge runs parallel to the walls. The area of a triangle depends only on its base and its perpendicular height, not on where the apex sits along that base, so a roof whose ridge is off-centre encloses exactly the same volume as a symmetric one of the same width and height. Move the ridge to one end entirely and you get a lean-to, which is a triangle of the same area — half the box, once again. What breaks the formula is a ridge that is not level or walls that are not parallel, since then the ends are different triangles and the shape stops being a prism.
- How much does the pitch change the roof surface?
- More than most people expect, because the slope length grows faster than the height does. Going from a 2 m ridge to a 4 m ridge on a 6 m width doubles the volume but raises the roof surface by only about 40 %, since each slope goes from 3.6 m to 5 m. That asymmetry is why steep roofs are common where volume is wanted and shallow ones where tiles are expensive. It also means a covering estimate must be taken from the slope length and never from the plan width, an error that under-orders material by exactly the factor the pitch introduces.
Articles you may find interesting
All guides →Related tools
Sources
Spotted a mistake in this article?