Skip to content
OneKitly

The Simple ABV Formula Under-Reports Strong Beer by Nine Per Cent

Published 11/6/2026 · 3 min read · Everyday calculators

Antonio Delgado

Antonio Delgado — Traditions & pastimes writer at OneKitly

Symbolism · Calendars

Checked against 2 sources

View profile →
In short

Alcohol content is worked out from how much the liquid's density fell during fermentation, since sugar is heavy and the alcohol replacing it is light. The familiar shortcut multiplies that drop by 131.25, and it is accurate enough for ordinary strengths: a wort at 1.050 finishing at 1.010 gives 5.25 % by the simple formula and 5.34 % by the more careful one, a difference of 1.7 %. Push the starting density to 1.090 and the same comparison gives 9.19 % against 9.99 %, a gap of nearly nine per cent — because the linear shortcut assumes a relationship that stops holding once there is a lot of alcohol present.

Advertisement

At 1.050 down to 1.010 the two formulas give 5.25 % and 5.34 %. At 1.090 down to 1.020 they give 9.19 % and 9.99 % — a gap that matters for labelling and for duty.

Attenuation is the other number on the readout

Alongside the strength, the calculator reports what fraction of the available sugar the yeast consumed: 80 % in the first example and 77.8 % in the second. That figure says more about how the fermentation went than the alcohol content does, because it is independent of how much sugar there was to begin with. A strain that normally attenuates to 75 % finishing at 85 % has been unusually thorough, and one stalling at 60 % has stopped early — a warning worth acting on before bottling, since sugar left behind can restart in the bottle and produce more pressure than the glass was designed for.

Temperature is the error nobody corrects

A hydrometer is calibrated at one temperature, usually 20 °C, and reads low in warm liquid because the liquid has expanded. A reading taken at 30 °C is roughly 0.002 too low, which is a quarter of a point of alcohol on a typical brew and enough to change a calculation that is already being reported to two decimals. Correction tables exist and are widely ignored, partly because the error is small relative to the strength and partly because it is invisible — nothing about the number looks wrong. The habit worth building is recording the temperature alongside the reading, which costs nothing and makes the correction possible later.

Two formulas at two strengths
Start and finishSimple formulaCareful formula
1.050 → 1.0105.25 %5.34 %
1.090 → 1.0209.19 %9.99 %

Worked with our own calculator

Homebrew ABV calculator

Given

Original gravity (OG)
1.05
Final gravity (FG)
1.01
Formula
Standard (×131.25)

Result

Alcohol by volume
5.25%
Apparent attenuation
80%

These figures are produced by the calculator below, not typed in by hand — they are recomputed whenever the tool changes.

Run it on your own figures →
Advertisement

Frequently asked questions

Where does the number 131.25 come from?
From fitting a straight line to measurements of how much density each unit of alcohol removes. The value has drifted over the years — older texts use 131, some use 131.25, some 132 — and the disagreement reflects that no single constant fits every case, which is the whole reason the more careful formula exists. Anyone comparing two published strengths for the same recipe should check which constant was used before concluding that the recipes differ. Four hundredths of a point separate the 131 and 132 conventions on an ordinary beer, and a published figure rarely says which was used.
Which formula should a label use?
Neither, strictly. Regulators generally require alcohol content to be measured rather than inferred, by distillation or by an instrument calibrated against it, and a hydrometer estimate is a working figure for the brewer rather than a legal one. Tolerances are usually specified as a fraction of a per cent, which is smaller than the gap between the two formulas on a strong beer. Anyone selling what they brew therefore needs a measurement; anyone brewing for themselves needs consistency more than accuracy, and should pick one formula and keep using it.

Articles you may find interesting

All guides →

Related tools

Sources

Spotted a mistake in this article?