Skip to content
OneKitly

Two Screens of the Same Diagonal Can Differ by a Quarter in Area

Published 11/10/2026 · 3 min read · Everyday calculators

Daniel Okonkwo

Daniel Okonkwo — Front-end developer and tech writer at OneKitly

Web performance · File formats

Checked against 2 sources

View profile →
In short

A rectangle's diagonal fixes neither its width nor its area — only the pair of them together. Take three panels all sold as 27 inches: the 4:3 measures 21.6 by 16.2 inches for 2258 cm² of glass, the 16:9 measures 23.53 by 13.24 for 2010 cm², and the 21:9 ultrawide measures 24.82 by 10.64 for 1703 cm². That is a spread of 555 cm², or a third of the smallest, between three things carrying the same headline number. The shift from 4:3 to 16:9 in the 2000s quietly shrank the area behind every diagonal by 11%, which is one reason a 17-inch laptop of 2004 does not feel smaller than a 17-inch laptop of today.

Advertisement

At 27 inches a 4:3 panel holds 2258 cm² and a 21:9 one holds 1703. The diagonal is the one number advertised and the one that hides the difference.

Why the diagonal became the number on the box

Cathode-ray tubes were round glass envelopes with a rectangle masked out of them, so the honest measure of the tube was its circular diameter and the diagonal of the visible picture came closest to it. The convention outlived the technology and now describes flat panels that have no circle anywhere in them. It survives because it is a single number that always sounds larger than either side, and because comparing areas would let a buyer notice that an ultrawide upgrade is often a downgrade in glass. Nothing about it is dishonest; it is just the least informative of the three numbers available.

The pixel diagonal nobody quotes

Run the same calculation on a resolution instead of a physical size and 1920 by 1080 gives a diagonal of 2202.91 pixels, while 3840 by 2160 gives 4405.81 — exactly twice, because doubling both sides doubles the diagonal too. That figure is the one a graphics driver cares about when it decides how far a cursor has travelled, and the one a game engine uses to normalise field of view across displays. It never appears on a spec sheet because it is not a selling point, but it is the length that actually gets computed thousands of times a second inside the machine.

Area
Three panels, one diagonal of 27 inches
ShapeWidth by height (in)Area
4:321.6 by 16.22258 cm²
16:923.53 by 13.242010 cm²
21:924.82 by 10.641703 cm²

Worked with our own calculator

Rectangle diagonal calculator

Given

Width
2
Height
2

Result

Diagonal
2.828
Area
4
Perimeter
8

These figures are produced by the calculator below, not typed in by hand — they are recomputed whenever the tool changes.

Run it on your own figures →
Advertisement

Frequently asked questions

How much wider is a 21:9 than a 16:9 of the same diagonal?
About 5% wider and 20% shorter. At 27 inches the ultrawide gains 1.28 inches of width and loses 2.60 inches of height, which is why it is a poor swap for reading and a good one for timelines. Anyone replacing a 16:9 with an ultrawide of the same diagonal is buying horizontal room by selling vertical room at a bad rate, and the only way to gain in both directions is to move up several inches of diagonal at the same time.
Does the same trap apply to televisions?
Less so, because televisions have settled on 16:9 almost universally, so diagonals there compare like with like. It bites hardest on phones, where aspect ratios have drifted from 16:9 to 19.5:9 and beyond: a 6.1-inch phone of 2016 and a 6.1-inch phone of today hold noticeably different amounts of screen, the newer one being taller and narrower. Whenever two devices share a diagonal but not a shape, the diagonal has stopped being a comparison and become a coincidence.

Articles you may find interesting

All guides →

Related tools

Sources

Spotted a mistake in this article?