Naar de inhoud
OneKitly

An Absorbance of Two Means One Per Cent of the Light Gets Through

Gepubliceerd op 19-10-2026 · 4 min leestijd · Dagelijkse calculators

Lena Hoffmann

Lena Hoffmann — Redacteur wetenschap en onderwijs bij OneKitly

Wiskunde · Natuurkunde

Getoetst aan 2 bronnen

Profiel bekijken →
Kort gezegd

The Beer–Lambert law says absorbance is the molar absorptivity times the concentration times the path length. With a molar absorptivity of 6,220 M⁻¹cm⁻¹, a 100 µM solution and a standard 1 cm cuvette, A comes to 0.622. What that number means is easy to misread: absorbance is a base-ten logarithm of the fraction of light blocked, so A = 0.622 lets 23.9 per cent of the beam through, A = 1 lets 10 per cent, A = 2 lets 1 per cent and A = 3 lets a thousandth. The relationship to concentration is perfectly linear — halving the sample halves A to 0.311, doubling the cuvette doubles it to 1.244 — but the relationship to the light reaching the detector is not, and that is where the measurement runs out.

Advertentie

6,220 M⁻¹cm⁻¹ at 100 µM through 1 cm gives A = 0.622, and 23.9 % of the light emerges. Double the path length and A doubles to 1.244 — the scale is logarithmic, and that is where it breaks.

Dilute until the number lands between 0.1 and 1

At A = 3 the detector is comparing a beam to a thousandth of itself, and every source of stray light, every scratch on the cuvette and every particle of dust contributes a larger share of what remains than the sample does. At A = 0.05 the opposite problem appears: the difference between sample and blank is smaller than the instrument's own drift. The usable band in between is where a spectrophotometer earns its keep, and getting into it is a matter of choosing the dilution or the cuvette — a 1 mm path instead of 10 mm divides the reading by ten without touching the sample at all, which is the fastest fix when material is scarce.

The absorptivity belongs to a compound at a wavelength

It is not a property of the machine or of the sample tube; it is a number for one substance measured at one wavelength in one solvent, and moving any of those three changes it. Quoting an absorptivity without the wavelength is like quoting a speed without a direction — the figure is real and the sentence is incomplete. It is also why a spectrophotometer is set to a specific wavelength before anything is measured, usually the peak of the compound's own absorption, where the reading is largest and least sensitive to the instrument being slightly off. A shift of a few nanometres near a steep flank of the spectrum can move the answer by more than the whole dilution error.

Light transmitted
Absorbance and the light that survives it
AbsorbanceLight transmittedVerdict
0.179.4 %Usable, near the noise floor
0.62223.9 %Comfortable
110 %Top of the good range
21 %Dilute the sample
30.1 %Not a measurement

Uitgewerkt met onze eigen calculator

Beer-Lambert-calculator (wet van Beer-Lambert)

Gegeven

Los op naar
Concentratie (c)
Absorbantie A (indien bekend)
1,244
Molaire extinctiecoëfficiënt ε (M⁻¹cm⁻¹)
12.440
Concentratie c
200
Eenheid concentratie
mM
Weglengte l (cm)
2

Resultaat

Resultaat
0,05

Deze cijfers komen uit de calculator hieronder, ze zijn niet met de hand ingetypt — ze worden opnieuw berekend telkens als de tool verandert.

Reken het door met je eigen cijfers →
Advertentie

Veelgestelde vragen

What is the blank actually for?
To subtract everything that is not the thing you are measuring. The solvent absorbs a little, the cuvette walls reflect a little, and the lamp is not equally bright at every wavelength; zeroing on a cuvette containing everything except the analyte removes all three in one step. A blank made from a different batch of solvent, or run in a different cuvette from the sample, quietly reintroduces what it was supposed to remove — which is why paired cuvettes exist and why the blank is remeasured whenever the wavelength changes.
Why does the law fail at high concentration?
For two reasons at once, one about the instrument and one about the chemistry. The instrumental one is stray light, which sets a ceiling on any reading: once the true transmission falls below the light leaking around the sample, further concentration changes nothing. The chemical one is that crowded molecules stop behaving independently — they interact, associate, and shift each other's absorption — so the absorptivity that was constant at micromolar concentrations is no longer the same number at millimolar. Both push the calibration curve to bend downward, which is why a standard curve is run across the range actually used rather than extrapolated from one point.

Artikelen die je misschien interesseren

Alle gidsen →

Vergelijkbare tools

Bronnen

Een fout in dit artikel gezien?