Naar de inhoud
OneKitly

Capacitors in Series: the Smallest One Decides, and Then It Fails

Gepubliceerd op 8-10-2026 · 3 min leestijd · Dagelijkse calculators

Daniel Okonkwo

Daniel Okonkwo — Front-enddeveloper en techredacteur bij OneKitly

Webprestaties · Bestandsformaten

Getoetst aan 2 bronnen

Profiel bekijken →
Kort gezegd

Capacitances in series add as reciprocals, exactly the way resistances do in parallel: 1 ÷ (1/100 + 1/220 + 1/330) = 56.9 µF. The result is always smaller than the smallest member, which is the opposite of what series does to resistors and the source of most of the confusion. The extreme case makes it obvious: 100 µF in series with 1 µF gives 0.99 µF, so the hundred-microfarad part contributes almost nothing to the total. What it also does is take almost none of the voltage. Charge is the same through a series string, so the voltage divides inversely with capacitance — across 100 volts, the 1 µF sees 99.01 V and the 100 µF sees 0.99 V. The small capacitor decides the capacitance and then absorbs the stress.

Advertentie

100, 220 and 330 µF in series come to 56.9 µF — less than the smallest. Put 100 µF and 1 µF in series and the total is 0.99 µF, while the small one carries 99 % of the voltage.

Why anyone puts them in series at all

Not for capacitance, which the arrangement reduces, but for voltage rating: two identical parts each rated 400 V make a string that can stand 800 V, at half the capacitance. The catch is that the split is only even while the two are genuinely identical, and real parts differ in tolerance and in leakage. The one that leaks less ends up holding more voltage, which stresses it more, which usually makes it leak less still. That runaway is why series strings in production carry balancing resistors across each capacitor — components whose only job is to force the division to stay where the design put it.

The tolerance is wider than the calculation

Reporting 56.9 µF from three nominal values implies a precision that the parts do not have. Electrolytic capacitors commonly carry tolerances of twenty per cent or worse, and their value drifts with temperature and with age as the electrolyte dries, so the string is somewhere in a band rather than at a point. That is fine for a smoothing or decoupling job, where any value above a minimum works, and it is not fine for a timing or filter circuit, where the value sets a frequency. For those, a film or ceramic part with a tight tolerance is the component the design actually needs, and the arithmetic is worth carrying to a decimal only once such a part is in the circuit.

Total
Series combinations, in microfarads
MembersTotal
100 + 10050.00
100 + 220 + 33056.90
100 + 10.99
Calculator condensatoren in serieBereken de totale capaciteit van condensatoren die in serie zijn geschakeld.Probeer de tool →
Advertentie

Veelgestelde vragen

And in parallel?
They simply add: 100 and 220 in parallel are 320 µF, and the voltage rating of the combination is that of the lowest-rated member rather than the sum. Parallel is the arrangement used when more capacitance is wanted, and it is also the reason a board carries several small decoupling capacitors instead of one large one — the small ones have lower internal inductance and respond faster, so the group behaves better at high frequency than any single part of the same total value.
Does the same formula work for any number of capacitors?
Yes — add the reciprocal of each and take the reciprocal of the sum, for two parts or for twenty. Two shortcuts are worth remembering because they come up constantly: n identical capacitors in series give one nth of the single value, so ten 100 µF parts make 10 µF, and two unequal ones can be done as the product over the sum. Beyond three parts the general form is quicker than any shortcut, and it is the one the calculation above uses.

Artikelen die je misschien interesseren

Alle gidsen →
UitlegA Camera Flash Holds Five Joules and Spends Them in a Millisecond100 µF at 330 V stores 5.44 J — less than a dropped apple. Released over a millisecond it is 5.4 kilowatts, which is why capacitors matter for power, not energy.UitlegA Capacitor Marked 220 Is Twenty-Two PicofaradsThe three digits are two figures and a count of zeros, in picofarads: 104 is 100 nF and 473 is 47 nF. The trap is 220, which is 22 pF — while a 220 pF part is marked 221.UitlegResistors in Series and in Parallel: The Formulas, and the Three Things They Do Not Tell YouSeries adds, parallel adds reciprocals — that part is easy. The parts that catch people: which member dominates the answer, why two 5 % resistors in parallel are still 5 %, and why the smallest resistor in a parallel pair takes the largest share of the power.UitlegSprings in Series Behave Like Resistors in ParallelTwo 500 N/m springs end to end give 250 N/m; side by side they give 1,000. Under the same 50 N load that is 0.2 m of travel against 0.05 m, and 5 joules stored against 1.25.UitlegA Coil Refuses to Stop, and the Bill Arrives as a SparkA 100 mH relay coil at 2 A holds 200 millijoules. Open the switch and that energy has one microsecond to find somewhere to go — usually across the contacts.UitlegThe 555 Cannot Give You a Fifty Per Cent Square WaveIn the standard astable circuit the output is high longer than it is low, always. With 10 kΩ and 47 kΩ the duty cycle is 54.8 %, and 50 % is a limit you approach but never reach.

Vergelijkbare tools

Bronnen

Een fout in dit artikel gezien?