A Camera Flash Holds Five Joules and Spends Them in a Millisecond
Gepubliceerd op 12-11-2026 · 3 min leestijd · Dagelijkse calculators
Daniel Okonkwo — Front-enddeveloper en techredacteur bij OneKitly
Webprestaties · Bestandsformaten
Getoetst aan 2 bronnen
A capacitor's energy is half the capacitance times the voltage squared, and the voltage term is what does the work. The 100 µF capacitor behind a camera flash charged to 330 V holds 5.44 joules, roughly what a 150 g apple gives up falling from a first-floor window. What makes it useful is the rate: dump that into a xenon tube over one millisecond and the power is 5.4 kilowatts, far beyond anything a battery could deliver directly. Double the voltage and the energy quadruples, which is why the charging whine goes up in pitch as the last volts arrive and why flash units are built around the highest voltage their insulation survives.
100 µF at 330 V stores 5.44 J — less than a dropped apple. Released over a millisecond it is 5.4 kilowatts, which is why capacitors matter for power, not energy.
Why capacitors never replaced batteries
A single AA cell holds around 13 000 joules, roughly two and a half thousand camera flashes' worth, in a package smaller than the flash capacitor. Chemistry stores energy in bonds and electrostatics stores it in a field, and the field is enormously less dense. What capacitors win on is speed and lifetime: they charge and discharge in microseconds and survive millions of cycles, where a battery manages hours and hundreds. Every design that pairs them — a camera, a defibrillator, a regenerative brake — is using the battery as the tank and the capacitor as the pump.
Charged is not the same as safe
A flash capacitor holds its charge for weeks after the batteries come out, and 5.4 joules at 330 volts through a finger is memorable rather than lethal. A defibrillator capacitor at 243 joules and 1800 volts is another matter entirely, and repair manuals for anything mains-powered start with a discharge procedure for a reason. The rule of thumb among technicians is that anything above about 100 volts and 1 joule deserves a bleed resistor and a check with a meter, and the capacitor does not care that the device has been unplugged since Tuesday.
| Use | Capacitor | Energy |
|---|---|---|
| Microcontroller decoupling | 100 µF at 12 V | 7.2 mJ |
| Camera flash | 100 µF at 330 V | 5.44 J |
| Defibrillator | 150 µF at 1800 V | 243 J |
Uitgewerkt met onze eigen calculator
Condensatorenergiecalculator
Gegeven
- Capaciteit (µF)
- 200
- Spanning (V)
- 24
Resultaat
- Energie (J)
- 0,058
- Energie (mJ)
- 57,6
Deze cijfers komen uit de calculator hieronder, ze zijn niet met de hand ingetypt — ze worden opnieuw berekend telkens als de tool verandert.
Reken het door met je eigen cijfers →Veelgestelde vragen
- Why does the energy depend on voltage squared?
- Because each additional bit of charge has to be pushed against the charge already there. The first electrons arrive easily; the last ones arrive against nearly the full voltage. Adding it all up gives half the total charge times the final voltage, which becomes half the capacitance times voltage squared. Exactly the same shape appears in a spring, where the last centimetre costs the most, and in both cases the halving factor is the average of a quantity that rose linearly from zero.
- What does a supercapacitor change?
- The capacitance, by a factor of a million, and the voltage downward by a factor of a hundred. A 3000 farad supercapacitor at 2.7 V holds 10 935 joules — genuinely battery-class, in exchange for a working voltage so low that they are almost always stacked in series. They fill the gap between the two technologies rather than replacing either, and are found where something must absorb a large amount of energy very quickly and repeatedly: tram braking, crane hoists, and the door mechanisms on some aircraft.
Artikelen die je misschien interesseren
Alle gidsen →Vergelijkbare tools
Bronnen
Een fout in dit artikel gezien?