A Coil That Is a Short Circuit at DC Is 628 Ohms at a Kilohertz
Gepubliceerd op 22-10-2026 · 3 min leestijd · Dagelijkse calculators
Daniel Okonkwo — Front-enddeveloper en techredacteur bij OneKitly
Webprestaties · Bestandsformaten
Getoetst aan 2 bronnen
Inductive reactance is two π times the frequency times the inductance, so a 100 millihenry coil opposes current with 31.4 ohms on a 50 hertz supply, 37.7 ohms on a 60 hertz one, and 628.3 ohms at a kilohertz. Set the frequency to zero and the reactance goes to zero as well: to steady current the coil is just its own wire resistance, usually a fraction of an ohm. That contrast is what makes an inductor useful as a filter — it passes what changes slowly and blocks what changes fast, which is the exact opposite of what a capacitor does, and the two together make every crossover, power-supply filter and radio tuner in existence.
100 mH presents 31.4 Ω at 50 Hz, 37.7 Ω at 60 Hz and 628.3 Ω at 1 kHz. The opposition is proportional to frequency and vanishes entirely at zero.
Reactance drops voltage without consuming power
Twelve volts across this coil at 60 hertz drives 0.318 amps, which looks exactly like a 37.7 ohm resistor from the outside — and yet the average power is not the 3.8 watts a resistor would burn. In an ideal inductor the current lags the voltage by a quarter cycle, so the instantaneous power is positive for half of each cycle and negative for the other half: the coil takes energy into its magnetic field and gives all of it back. The 3.8 figure is reactive power, which circulates rather than being consumed, and it is why the electricity meter on a house is happier with a heater than with a large motor drawing the same current.
The same coil is three different components
At mains frequency 100 millihenrys is a mild obstacle you might not notice; at a kilohertz it is a serious one; at a megahertz the same formula gives 628 kilohms, and the coil is effectively an open circuit. Real inductors give up before that, because the winding's own stray capacitance eventually resonates with the inductance and the component starts behaving like a capacitor instead — every inductor has a frequency above which it stops being an inductor. Choosing one therefore means checking that its self-resonant frequency sits well above the band you care about, a specification that datasheets print and beginners routinely skip.
| Frequency | Reactance |
|---|---|
| 0 Hz (DC) | 0 Ω |
| 50 Hz | 31.4 Ω |
| 60 Hz | 37.7 Ω |
| 1 kHz | 628.3 Ω |
Uitgewerkt met onze eigen calculator
Inductieve-reactantiecalculator
Gegeven
- Oplossen naar
- Frequentie f
- Frequentie f
- 120
- Eenheid van f
- kHz
- Zelfinductie L
- 200
- Eenheid van L
- mH
- Reactantie XL (bij oplossen naar f of L)
- 5
- Eenheid van XL
- kΩ
- Effectieve spanning (optioneel)
- 5 V
Resultaat
- Inductieve reactantie XL
- 5.000 Ω
- Frequentie
- 3.979 Hz
- Zelfinductie
- 200 mH
- Stroom (als er een spanning is)
- 0,001 A
- Blindvermogen (als er een spanning is)
- 0,005 VAR
Deze cijfers komen uit de calculator hieronder, ze zijn niet met de hand ingetypt — ze worden opnieuw berekend telkens als de tool verandert.
Reken het door met je eigen cijfers →Veelgestelde vragen
- Why does a motor draw a huge current at switch-on?
- Because at the instant of starting it is not yet turning, and a turning motor generates a voltage of its own that opposes the supply. Stationary, the only thing limiting the current is the winding's resistance and reactance, which together are far smaller than what the running machine presents. The inrush lasts only as long as the motor takes to come up to speed, but it can be several times the running current, which is why motor circuits use slow-blow fuses and why a large motor starting on a weak supply visibly dips the lights.
- How does this combine with resistance in a real circuit?
- Not by adding. Resistance and reactance are at right angles to each other in the sense that matters, so the total opposition — the impedance — is the square root of the sum of their squares. A 30 ohm resistor in series with 40 ohms of reactance gives 50 ohms of impedance rather than 70, and the familiar 3-4-5 triangle turns up because the arithmetic is the same. Adding them directly is one of the most common early mistakes in alternating-current work, and it always overstates the opposition, sometimes badly.
Artikelen die je misschien interesseren
Alle gidsen →Vergelijkbare tools
Bronnen
Een fout in dit artikel gezien?