Naar de inhoud
OneKitly

The Same Impedance at 50 Hz and 1 kHz, With Opposite Signs

Gepubliceerd op 29-10-2026 · 3 min leestijd · Ontwikkelaarstools

Daniel Okonkwo

Daniel Okonkwo — Front-enddeveloper en techredacteur bij OneKitly

Webprestaties · Bestandsformaten

Getoetst aan 2 bronnen

Profiel bekijken →
Kort gezegd

Impedance has a size and a sign, and reporting only the size loses the plot. In a series circuit of 100 Ω, 50 mH and 10 µF, the magnitude is 318.7 Ω at 50 Hz and 314.6 Ω at 1 kHz — near enough identical — but the phase is −71.7° at the low frequency and +71.5° at the high one. Below the resonant point the capacitor dominates and current leads the voltage; above it the inductor dominates and current lags. At 225.1 Hz the two reactances cancel exactly, the phase passes through zero, and the impedance collapses to the resistance alone: 100 Ω, the smallest value this circuit can present at any frequency.

Advertentie

A 100 Ω, 50 mH, 10 µF series circuit shows 319 Ω at 50 Hz and 315 Ω at 1 kHz. Between them, at 225 Hz, it collapses to exactly 100 Ω.

The reactances swap places, not the components

At 50 Hz the inductor offers 15.7 Ω and the capacitor 318.3 Ω; at 1 kHz the inductor offers 314.2 Ω and the capacitor 15.9 Ω. The two have almost exactly traded values, which is why the magnitudes match while everything about the circuit's behaviour has inverted. Inductive reactance rises in direct proportion to frequency and capacitive reactance falls in inverse proportion, so on a logarithmic frequency axis the two curves are mirror images crossing at one point. That crossing is the resonance, and its position depends only on the inductance and the capacitance — the resistance sets how deep the notch goes, not where it sits.

Why the sign matters more than the number

A reactive load draws current that is out of step with the voltage, and the part that is out of step does no work: it sloshes back and forth between the source and the component, heating the wiring on both journeys. This is what power factor measures, and why industrial customers are billed for it. Correcting a factory's lagging, inductive load means adding capacitance to push the phase back towards zero — the same cancellation the calculator shows at 225 Hz, applied deliberately at 50 Hz by choosing the capacitor to suit the machinery. Reporting a load as 'about 319 ohms' without its sign is exactly the information a correction calculation cannot use.

Magnitude
One circuit, three frequencies
FrequencyMagnitudePhase and character
50 Hz318.7 Ω−71.7°, capacitive
225.1 Hz100.0 Ω0°, resistive
1 000 Hz314.6 Ω+71.5°, inductive

Uitgewerkt met onze eigen calculator

Impedantiecalculator (RLC)

Gegeven

Topologie van de kring
Serie-RLC
Weerstand R
100
Eenheid van R
Ω
Zelfinductie L
50
Eenheid van L
H
Capaciteit C
10
Eenheid van C
F
Frequentie f
1
Eenheid van f
Hz

Resultaat

Impedantiemodulus |Z|
329,676 Ω
Fasehoek
72,342 °
Inductieve reactantie XL
314,159 Ω
Capacitieve reactantie XC
0,016 Ω
Resonantiefrequentie f₀
0,007 Hz

Deze cijfers komen uit de calculator hieronder, ze zijn niet met de hand ingetypt — ze worden opnieuw berekend telkens als de tool verandert.

Reken het door met je eigen cijfers →
Advertentie

Veelgestelde vragen

What happens to the voltage across the components at resonance?
It can exceed the supply voltage, which surprises people the first time they measure it. At 225 Hz each reactance is about 70.7 Ω while the resistance is 100 Ω, so the voltage across the inductor and across the capacitor is roughly 70 % of the total — modest here. Lower the resistance to 5 Ω and the current rises fourteen-fold; the reactive voltages then reach fourteen times the input while still cancelling each other exactly. Series resonant circuits with low resistance are therefore a way to generate high voltages from a small source, and a way to destroy components rated for the supply voltage alone.
Is a parallel circuit the same story?
The same physics, inverted. In parallel the reactances still cancel at the same frequency, but the effect is a maximum rather than a minimum: the circuit presents its largest impedance at resonance and admits almost no current there. That is the arrangement used to select one station out of many, since a high impedance at the wanted frequency and a low one everywhere else is exactly a filter that passes one narrow band. The series version, presenting a minimum, is used the other way round — to shunt an unwanted frequency to ground while leaving the rest of the spectrum alone.

Artikelen die je misschien interesseren

Alle gidsen →

Vergelijkbare tools

Bronnen

Een fout in dit artikel gezien?