The Cone You Cut From Paper Is a Sector, Not a Triangle
Published 11/10/2026 · 3 min read · Everyday calculators
Marco Bianchi — Home, DIY & motoring writer at OneKitly
Renovation · Materials
Checked against 2 sources
A cone's surface is the base circle plus the curved side, and the side depends on the slant height rather than the vertical one. Radius 5 with height 12 gives a slant of 13 — the 5-12-13 right triangle standing up inside the cone — and a total surface of 282.74. Radius 3 with height 4 gives a slant of 5, the other familiar triple. Cut the curved surface open and flatten it and you get a sector of a circle of radius 13, whose arc equals the base circumference. Rolling a triangle instead produces a shape that does not close, which is the standard first failure when making a paper cone by eye.
Radius 5 and height 12 give a slant of 13 and a surface of 282.74. Flattened out, the curved part is a pie slice of radius 13 — never a triangle.
The angle to cut, and where it comes from
The flattened side is a sector whose arc has to match the base circumference exactly, or the cone gapes or overlaps. The fraction of a full circle it takes is the base radius divided by the slant: for 5 and 13 that is 0.385, which is 138.5° of the 360. Cut more and the cone is too shallow; cut less and it will not close. Lampshade makers and funnel makers work from that ratio directly, and it is the one number a template must carry — everything else about the finished shape follows from it.
Slant is what the tape reaches and height is what the formula wants
For a surface calculation the slant is the useful measurement and it is also the accessible one — a tape laid up the outside of a cone reads it directly. For a volume calculation it is the vertical height that matters, and that has to be computed rather than measured. The pair is the same trap the roof and the pyramid set, and the escape is the same: measure whichever you can reach, then let Pythagoras supply the other. Recording which one was measured is the part people skip, and a note saying '13 (slant)' costs nothing and saves the argument later.
| Radius and height | Slant | Total surface |
|---|---|---|
| 3 and 4 | 5 | 75.40 |
| 5 and 12 | 13 | 282.74 |
| 8 and 15 | 17 | 628.32 |
Worked with our own calculator
Cone surface area calculator
Given
- Radius
- 6
- Height
- 8
Result
- Total surface area
- 301.593
- Slant height
- 10
These figures are produced by the calculator below, not typed in by hand — they are recomputed whenever the tool changes.
Run it on your own figures →Frequently asked questions
- Does the surface include the base?
- Here it does, which is right for a solid cone and wrong for a funnel. The curved part alone is π times radius times slant — 204.20 for the 5-and-13 case — and the base adds a further 78.54. Anything open at the bottom needs only the first figure, and using the total overstates material by 38% on the 5-and-13 cone and by more on a shallower one. Party hats, funnels, filter papers and traffic cones all fall on the open side; ice cream cones and hoppers do not.
- Why do so many examples land on whole numbers?
- Because they are chosen to. The slant is a hypotenuse, so a whole-number answer needs the radius and height to form a Pythagorean triple — 3-4-5, 5-12-13, 8-15-17 and their multiples. Those are rare enough that a textbook reuses the same handful for a century, and common enough that anyone who has done a few problems recognises them on sight. Real cones almost never comply: a cone of radius 5 and height 10 has a slant of 11.18, and the whole-number cases exist to spare the reader arithmetic rather than to describe anything.
Articles you may find interesting
All guides →Related tools
Sources
Spotted a mistake in this article?